axismd.ai
Siemens SINUMERIK Controller
Program/G-code · Intermediate · 30-120 minutes
Siemens 14404 - Block illegal parameterization of transformation
Error has occurred when selecting transformation. Possible causes of error: - An axis traversed by the transformation has not been enabled: - is being used by another channel (-> enable) - is in spindle mode (-> enable with SPOS) - is in POSA mode (-> enable with WAITP) - is concurrent Pos axis (-> enable with WAITP) - Parameterization via machine data has an error - Axis or geometry axis assignment to the transformation has an error, - Machine data has an error (-> modify machine data, restart) Please note: Any axes not enabled might be signaled via alarm 14092 or alarm 1011 instead of alarm 14404. Transformation-dependent error causes can be in: TRAORI: - TRANSMIT: - The current machine axis position is unsuitable for selection (e.g. selection in the pole) (-> change position slightly). - Parameterization via machine data has an error. - Special requirement with respect to the machine axis has not been fulfilled (e.g. rotary axis is not a modulo axis) (-> modify machine data, restart). Alarms NCK alarms TRACYL: The programmed parameter is not allowed when transformation is selected. TRAANG: - The programmed parameter is not allowed when transformation is selected. - Parameterization via machine data has an error. - Parameter is faulty (e.g. TRAANG: unfavorable angle value (-> modify machine data, restart) Persistent transformation: - Machine data for persistent transformation are wrong (-> consider dependencies, change machine data, restart) Only with active "OEM transformation" compile cycle: The axes included in the transformation must be referenced Control reaction: Correction block is reorganized. Interface signals are set. Alarm display.
14404
Siemens 14404 - Block illegal parameterization of transformation
Block illegal parameterization of transformation
Error has occurred when selecting transformation. Possible causes of error: - An axis traversed by the transformation has not been enabled: - is being used by another channel (-> enable) - is in spindle mode (-> enable with SPOS) - is in POSA mode (-> enable with WAITP) - is concurrent Pos axis (-> enable with WAITP) - Parameterization via machine data has an error - Axis or geometry axis assignment to the transformation has an error, - Machine data has an error (-> modify machine data, restart) Please note: Any axes not enabled might be signaled via alarm 14092 or alarm 1011 instead of alarm 14404. Transformation-dependent error causes can be in: TRAORI: - TRANSMIT: - The current machine axis position is unsuitable for selection (e.g. selection in the pole) (-> change position slightly). - Parameterization via machine data has an error. - Special requirement with respect to the machine axis has not been fulfilled (e.g. rotary axis is not a modulo axis) (-> modify machine data, restart). Alarms NCK alarms TRACYL: The programmed parameter is not allowed when transformation is selected. TRAANG: - The programmed parameter is not allowed when transformation is selected. - Parameterization via machine data has an error. - Parameter is faulty (e.g. TRAANG: unfavorable angle value (-> modify machine data, restart) Persistent transformation: - Machine data for persistent transformation are wrong (-> consider dependencies, change machine data, restart) Only with active "OEM transformation" compile cycle: The axes included in the transformation must be referenced Control reaction: Correction block is reorganized. Interface signals are set. Alarm display.
Safety
- Only qualified personnel should diagnose and clear control alarms; follow the machine builder's safety procedures and lockout/tagout where hardware work is required.
Common Causes
- Error has occurred when selecting transformation.
- Possible causes of error: - An axis traversed by the transformation has not been enabled: - is being used by another channel (-> enable) - is in spindle mode (-> enable with SPOS) - is in POSA mode (-> enable with WAITP) - is concurrent Pos axis (-> enable with WAITP) - Parameterization via machine data has an error - Axis or geometry axis assignment to the transformation has an error, - Machine data has an error (-> modify machine data, restart) Please note: Any axes not enabled might be signaled via alarm 14092 or alarm 1011 instead of alarm 14404.
- Transformation-dependent error causes can be in: TRAORI: - TRANSMIT: - The current machine axis position is unsuitable for selection (e.g. selection in the pole) (-> change position slightly).
Troubleshooting Steps
- 1Please inform the authorized personnel/service department.
- 2Modify part program or machine data.
- 3Only with active "OEM transformation" compile cycle: Reference the axes included in the transformation before selecting transformation.
- 4Clear alarm with NC START or RESET key and continue the program
Seeing Multiple Alarms?
Seeing another alarm with this one? Enter the code.
Get machine-aware diagnosis
AxisMD logs alarms against your actual machines, tracks patterns, and gives AI context your manual doesn't have.
Start freeWas this guide helpful?
Always verify with your machine manual or a certified technician before performing service procedures.